Green BMW with the plate removed, only the Mag magnet bases left on the bumper
The same BMW with the front plate attached on a Mag holder

Off in a second.
Back in a click.

Fast magnetic plate holders with no screws. The plate snaps on and comes off in one pull.

See the products Drag the image to see the difference

Two holders, one idea

Back of a license plate with Mag magnets attached, held in front of a green BMW
FINMAG

40 €Free shipping

Magnetic plate holder. Powerful neodymium magnets and a truly slim design.

Mount
N52 neodymium magnets
Base
3M VHB tape, no drilling
Design
Only 8 mm thick
Colors
Black or white
Removal
Pull off by hand
In the box
4 × mounts with counterparts
4 × stabilizers
One pack
Front and rear plate
Buy Mag
Rear of a green BMW with only the two low Klip mounts left where the plate was
FINKLIP

25 €Free shipping

Clip-on holder. The plate locks in with a click and releases just as fast. A light, affordable choice for your daily driver.

Mount
Locking clip
Base
Screw mount
Tested
1000+ on/off cycles
Colors
Black or white
In the box
4 × clip holders
4 × screws, 5 × 20 mm (Torx T20)
4 × 3M VHB tape
One pack
Front and rear plate
Buy Klip

Made in Finland

Every Platevo holder is made in Finland. We choose the best materials on the market, because they are what keeps your plate in place.

Magnets
N52 neodymium
Tape
3M VHB
Plastic
ASA
Made in
Finland

Installation takes a few minutes

Mag is mounted entirely with 3M VHB tape, no tools or drilling needed. Klip is screwed into your car's existing plate holes or through a plastic bumper, and the plate sticks to the clips with VHB tape.

  1. Attach the bases

    Clean the surfaces with isopropyl alcohol. Mag: stick the magnet parts onto the car with the VHB tape. Klip: screw the clips into the old plate holes or through a plastic bumper.

  2. Attach the plate

    Line the plate up straight and press it onto the counterparts or clips with VHB tape. The tape reaches full strength in 72 hours.

  3. Remove when needed

    Pull the plate off by hand for a photo shoot and put it back just as quickly.

QR code linking to Platevo installation videos on TikTok

Watch the installation videos

Step-by-step videos for both Mag and Klip. Scan the code or tap the link.

Rear of a BMW with only the holder base left in place
With the plate off, only the sleek counterparts are left.

Questions and answers

Will the plate stay on at highway speeds?

Yes. We have tested the holders at speeds up to 280 km/h, and the plates stayed firmly in place. The magnets and clip hold tight on bumpy roads too.

Does it work all year round?

Yes. Our plates have been in year-round test use through Finnish winters, rain and road salt with no problems. Mag has no moving parts to freeze.

Will it fit my car?

Klip fits most cars where the plate is already attached with 4–5 mm thick screws. Mag fits cars where the stabilizers can be placed as high and as low as possible behind the plate, so the plate stays stable at all times. If you're unsure, tell us your car model and we'll confirm.

What's the difference between Mag and Klip?

Mag (40 €) is a magnetic holder: it comes off in one pull and leaves a cleaner base. Klip (25 €) locks in with a click and is the lighter, more affordable option. Shipping is free for both.

How long does delivery take?

Most holders are made to order. Making yours takes about one day, and shipping takes 1–4 business days.

Can I get a custom order?

Yes. We can tailor the Mag holder to your car, for example a stronger pull force with thicker magnets or a different stabilizer size. Both holders come in black or white. Tell us what you need and we'll make it.

Can I drive without a plate?

No. License plates must be attached whenever the car is driven. Platevo lets you remove the plate for photo shoots, car shows or storage, and put it back quickly.

Can the installation be undone?

Yes. Mag's VHB tape can be removed by warming it up, and Klip's clips unscrew from the same holes.

Refund policy

14 days to change your mind

You can return your order within 14 days of receiving it, without giving a reason. This doesn't limit any of your rights under Finnish or EU consumer law.

How to return

  1. Email us at info@platevo.fi with your order number and, if you like, the reason for the return. You can use our .
  2. Wait for our reply. We'll confirm the return and send you the return address and instructions.
  3. Send the item back within 14 days of telling us you want to return it.

Condition of the item

Please return the holder unused and in its original packaging, together with your receipt or order confirmation. If the item has been used or installed beyond what's needed to check it, we may deduct the loss in value from the refund.

Return shipping

Return shipping is paid by you, unless the return is our fault: the item is faulty, damaged in transit or not what you ordered. In those cases we cover the shipping.

Refunds

Once we've received and checked the item, we refund the full price to your original payment method within 14 days. Depending on your bank, it may take a few more days to show on your account. If you haven't seen it after that, contact us.

Faulty, damaged or wrong item?

Check your order when it arrives. If something is wrong, let us know as soon as possible and include a few photos and a short description. Once we've confirmed the problem, you can choose a replacement or a full refund, at no cost to you.

Custom orders

Holders made to your own specifications, for example with thicker magnets or a different stabilizer size, can't be returned under the 14-day right. Your rights for faulty products still apply.

Exchanges

We don't swap items directly. Return the original item, and once the return is confirmed, place a new order for the one you want.

Questions? Email info@platevo.fi.
Platevo, Business ID 3670132-7

Terms of sale & delivery

1. Seller

SellerPlatevo
Business ID3670132-7
AddressPuusepänkaarre 2, 06150 Porvoo, Finland
Emailinfo@platevo.fi

2. Ordering

Press the buy button for the holder you want. You'll go to Stripe's secure checkout, where you choose the color, enter your delivery address and pay. The purchase is complete once your payment has been accepted, and you'll get a confirmation by email. For custom orders, email us at info@platevo.fi.

3. Prices

Prices are in euros and are the final prices you pay. Delivery within Finland is free. Mag costs 40 € and Klip 25 €. The price that applies is the one shown when you place your order. Platevo is not registered for VAT (small business exemption, section 3 of the Finnish VAT Act), so no VAT is included in or added to the prices.

4. Payment

Payments are handled by Stripe. The available payment methods are shown on the payment page. Your card details go directly to Stripe, and Platevo never sees them.

5. Delivery

We deliver within Finland only, through Posti. Most holders are made to order: making yours takes about one day, and delivery takes 1–4 business days. If your order is going to be delayed, we'll let you know. If the delay is significant, you can cancel the order and get a full refund.

6. Right of withdrawal

You have 14 days from receiving your order to cancel it without giving a reason. To cancel, tell us clearly by email at info@platevo.fi. You can use our , but it isn't required. Custom orders made to your specifications are not covered by the right of withdrawal. Returns and refunds are explained in more detail in our refund policy.

7. Defects and warranty

Our products are covered by the seller's liability for defects under the Finnish Consumer Protection Act. Platevo also gives a 1-year warranty against material and manufacturing defects, as described in the installation & safety guide. If you find a fault, email info@platevo.fi with a few photos.

8. Disputes

If something goes wrong, please contact us first. We'll do our best to sort it out. If we can't agree, you can contact the Finnish consumer advisory service (kkv.fi) and take the matter to the Consumer Disputes Board (kuluttajariita.fi). Before going to the Board, you need to contact consumer advisory services. You can also take the matter to your local district court.

9. Changes

These terms are valid from 22 November 2026. The terms in force when you place your order apply to that order.

Privacy policy

1. Controller

Platevo, Business ID 3670132-7, Puusepänkaarre 2, 06150 Porvoo, Finland. Contact: info@platevo.fi.

2. What data we collect

You enter your order details (name, email, delivery address and chosen color) on Stripe's checkout page, and they're passed to us so we can deliver your order. Card and payment details are handled by Stripe. We don't see or store them.

3. Why we use it

We don't send marketing unless you've asked for it, and we never sell your data.

4. Who we share it with

Some of these providers, such as Stripe, may process data in the United States. Those transfers are based on the EU–US Data Privacy Framework or the European Commission's standard contractual clauses.

5. How long we keep it

Order and bookkeeping records are kept as long as the Accounting Act requires, generally 6 years from the end of the financial year. Other messages are deleted once the matter is closed, at the latest after 2 years.

6. Cookies

This website doesn't use cookies or analytics. Your language choice is saved in your own browser (localStorage) and is never sent to us. Our hosting provider may keep short-term technical logs, such as IP addresses, for security. Links to TikTok take you to TikTok, where TikTok's own privacy policy applies.

7. Your rights

You have the right to see the data we hold about you, to have it corrected or deleted, to restrict or object to its use, and to get it in a portable format. Email info@platevo.fi. If you think we've handled your data wrongly, you can complain to the Data Protection Ombudsman (tietosuoja.fi).

Last updated 22 November 2026.

Withdrawal form

Fill in and send this form only if you want to cancel your purchase. You can also cancel with a free-form email.

To: Platevo, Puusepänkaarre 2, 06150 Porvoo, Finland, info@platevo.fi

I hereby give notice that I withdraw from my contract of sale of the following goods:

Product(s):
Order number:
Ordered on / received on:
Name of consumer:
Address of consumer:
Signature of consumer (only if this form is sent on paper):
Date:

Open as an email

Installation & safety guide

Platevo Mag / Klip, magnetic and clip-on license plate holders. Installation and safety guide, version 1.0, 11/2026.
Read the whole guide before installing and keep it for later. If you pass the product on, pass this guide on with it.

1. Manufacturer

ManufacturerPlatevo
Business ID3670132-7
Emailinfo@platevo.fi
Websiteplatevo.fi
Product IDMag-01 / Klip-01

2. Safety warnings

3. In the box

Mag holder (Mag-01)

PartQtyNotes
Magnet part, attaches to the car4Neodymium magnet, ASA, 21 mm disc
Counterpart, attaches to the plate4Neodymium magnet, ASA, 26 × 40 mm
Mounting tape83M VHB 5952
Spacers / vibration dampers4ASA

Klip holder (Klip-01)

PartQtyNotes
Clip holder, attaches to the car4ASA
Screws45 × 20 mm, Torx T20
Mounting tape43M VHB 5952

Check the contents before installing. If something is missing, email info@platevo.fi.

4. Before installing and legal use

You'll need: a Torx T20 key for Klip, a cleaner (isopropyl alcohol), a clean cloth and safety glasses.

5. Installing Mag

Mag is mounted with 3M VHB tape only: the magnet parts go on the car's plate area and the counterparts on the plate. No screws needed.

  1. Clean the surfaces. Wipe the mounting area on the car and the back of the plate with isopropyl alcohol and let them dry.
  2. Attach the magnet parts to the car. The tape is already on the bottom of each magnet part. Peel off the liner, press the part onto a flat spot on the plate area and hold for 30 seconds. The recommended installation temperature is +21…+38 °C. Don't install on a cold surface. Plastic surfaces may need an adhesion promoter (primer).
  3. Leave the counterparts in place. They come attached to the magnets, so they're already in the right position. Don't remove them before the plate is attached.
  4. Test-fit the plate. Check that it's straight and centered before peeling off the tape liner.
  5. Attach the plate to the counterparts. Peel off the liner and press the plate evenly into place. Put the tape on a flat area, not on top of raised letters or numbers.
  6. Let the tape cure. At room temperature the tape reaches 50% of its strength in 20 minutes, 90% in 24 hours and full strength in 72 hours. Curing is slower in the cold, so keep the plate somewhere warm indoors if you can.
  7. Test it. Attach the plate and pull it gently in different directions. It must not move or rattle.

6. Installing Klip

The Klip screws go into the bumper with an adapter, the brackets go onto the screws, and the plate attaches to the brackets with VHB tape.

  1. Clean the surfaces. Wipe the mounting area on the bumper and the back of the plate with isopropyl alcohol and let them dry.
  2. Fit the screws to the bumper. Use the adapter to attach the screws either to the plate mounting points or straight through a plastic bumper. Tighten by hand.
  3. Fit the brackets onto the screws. Make sure they're level and symmetrical.
  4. Attach the plate. Peel the liner off the brackets' VHB tape, line the plate up straight and centered, and press it evenly into place. The recommended installation temperature is +21…+38 °C.
  5. Let the tape cure. 50% strength in 20 minutes, 90% in 24 hours and full strength in 72 hours at room temperature. Curing is slower in the cold.
  6. Test it by pulling gently. The plate must not rattle.

Removing the plate: lift the plate evenly from its bottom edge. Don't twist it from one corner, or the holder may get damaged.

7. Use, care and checks

8. Warranty, claims and returns

9. Recycling

Take metal parts to metal recycling. Sort plastic parts and packaging according to your local recycling rules.

Questions about installing? Email info@platevo.fi.
Platevo, Business ID 3670132-7